![]() If running on CentOS or RHEL based distros you can replace instances of sudo apt with sudo yum. The methods above can be applied to any supported PHP versions. To remove all PHP 8.1 packages after upgrading to PHP 8.2 run the commands below. If you have more than one or older PHP versions running you can disable the old module and enable the new one using the following.Įnable PHP 8.2 as the main PHP version: $ sudo a2enconf php8.2-fpmĭisable PHP 8.1 FPM extension completely. You can omit the FilesMatch block in the configuration block if your main PHP version is PHP 8.2 Bonus: Removing Old PHP and extensions Reload the Apache web server to apply the changes: $ sudo systemctl reload apache2 ![]() SetHandler "proxy:unix:/run/php/|fcgi://localhost/"ĬustomLog $/access.log combinedĮnable the new virtual host by running the following command: $ sudo a2ensite Options -Indexes +FollowSymLinks +MultiViews Inside the new configuration file, add the following configuration with PHP-FPM: You can do this by running the following command: $ sudo a2enmod proxy_fcgi proxyĬreate a new configuration file for your virtual host using the following command: $ sudo nano /etc/apache2/sites-available/ To configure Apache to use PHP-FPM, you need to enable the “proxy_fcgi” and “proxy” modules. You can also enable PHP-FPM to start at boot time by running the following command: $ sudo systemctl enable php8.2-fpm Configure Apache to use PHP8.2-FPM Once the installation is complete, you can start the PHP-FPM service by running the following command: $ sudo systemctl start php8.2-fpm $ sudo systemctl restart apache2 Option 2: Using PHP 8.2 – FPM Next enable mod_php module: $ sudo a2enmod php8.2 Install both Apache and PHP, and any other necessary PHP extensions including the Apache PHP module like so: $ sudo apt install apache2 libapache2-mod-php8.2 It is responsible for processing PHP code directly within the Apache process. The Apache mod_php module, which is built into Apache. Nginx: configuration file /etc/nginx/nf test is successful Using PHP 8.2 with ApacheĪpache web server can use PHP as an Apache PHP module or as a FastCGI Process Manager (PHP-FPM). Nginx: the configuration file /etc/nginx/nf syntax is ok Safe and exit the file then verify Nginx configuration using this command: $ sudo nginx -t This can be done by editing the Nginx configuration and add the following block inside the http block to configure Nginx to forward PHP requests to PHP-FPM: $ sudo nano /etc/nginx/nfįastcgi_pass unix:/var/run/php/ Once Nginx and FPM extension are installed, you will need to configure Nginx to forward incoming requests to PHP-FPM. If you haven’t installed Nginx you will need to install it together PHP-FPM by running the following command: $ sudo apt install nginx php8.2-fpmĪs you can see above PHP-FPM comes as a PHP extension. Nginx acts as a reverse proxy, forwarding incoming requests to PHP-FPM to be executed. PHP-FPM is a daemon that listens for incoming PHP requests and runs them in a separate process. ![]() With Nginx, PHP code is typically executed by a separate process called FastCGI Process Manager (PHP-FPM). In the examples below will assume you are using Debian based distros Using PHP 8.2 with Nginx You can use PHP with either Nginx or Apache web server to create your dynamic and interactive web pages using the following instructions depending on your choice of web server. ![]() Installing PHP 8.2 on CentOS and RHEL systems.If you do not have PHP 8.2 on your Linux systems, we have already published a series of guides showing how you can install it on difference platforms as follows: In this guide we will be showing you how to use PHP 8.2 with Nginx and Apache web Servers. The most likely use case for PHP is in conjuction with a web server. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |